200Gb/s QSFP DD PSM8 10km Optical Transceiver
Products
Home /

Optical Transceivers

/

200G Optical Transceiver

/200Gb/s QSFP DD PSM8 10km Optical Transceiver

200Gb/s QSFP DD PSM8 10km Optical Transceiver
200Gb/s QSFP DD PSM8 10km Optical Transceiver

200Gb/s QSFP DD PSM8 10km Optical Transceiver

The FiberWDM RQD-200G10-PSM8 is a Eight-Channel, Pluggable, Parallel, Fiber-Optic QSFP DD PSM8 for 2×100 Gigabit Ethernet , Infiniband DDR/EDR Applications. This transceiver is a high performance module for data communication and interconnect applications. It integrates eight data lanes in each direction with 208 Gbps bandwidth. Each lane can operate at 26Gbps up to 10km over G.652 SMF. These modules are designed to operate over singlemode fiber systems using a nominal wavelength of 1310nm. The electrical interface uses a 76 contact edge type connector. The optical interface uses an 24 fiber MTP (MPO) connector. This module incorporates FiberWDM proven circuit and Optical technology to provide reliable long life, high performance, and consistent service. 

Inquire now
  • Product Detail

200Gb/s QSFP DD PSM8 10km Optical Transceiver  RQD-200G10-PSM8

 

Features

 

  • 8 channels full-duplex transceiver modules
  • Supports 8×25Gb/s aggregate bit rates
  • Supports 8×10Gb/s aggregate bit rates if required
  • 8 channels 1310nm DFB
  • 8 channels PIN photo detector array
  • Internal CDR circuits on both receiver and transmitter channels
  • Support CDR bypass
  • Low power consumption <6.5W
  • Hot Pluggable QSFP DD form factor
  • Up to 10km reach for G.652 SMF
  • Single male MPO(APC 8-degree) connector receptacle
  • Operating case temperature 0°C to +70°C
  • 3.3V power supply voltage
  • RoHS 2.0 compliant (lead free)

 

Applications

 

  • 2×100G Ethernet links
  • Infiniband DDR/EDR
  • Datacenter and Enterprise networking

 

Figure 1. Module Block Diagram

 

The 200Gb/s QSFP DD PSM8 is one kind of parallel transceiver. DFB and PIN array package is key technique, through I2C system can contact with module.

 

Absolute Maximum Ratings

 

Parameter Symbol Min Min Unit
Supply Voltage Vcc -0.3 3.6 V
Input Voltage Vin -0.3 Vcc+0.3 V
Storage Temperature Ts -20 85 ºC
Case Operating Temperature Tc 0 70 ºC
Humidity (non-condensing) Rh 5 95 %

 

Recommended Operating Conditions

 

Parameter Symbol Min Typical Max Unit
Supply Voltage Vcc 3.13 3.3 3.47 V
Operating Case Temperature Tc 0   70 ºC
Data Rate Per Lane fd 10.3125 25.78125   Gbps
Humidity Rh 5   85 %
Power Dissipation Pm   5.28 6.5 W
Fiber Bend Radius Rb 0.002   10 km

 

Electrical Specifications

 

Parameter Symbol Min Typical Max Unit
Differential Input Impedance  Zin 90 100 110 ohm
Differential Output Impedance Zout 90 100 110 ohm
Differential Input Voltage Amplitude1 ΔVin 190   700 mVp-p
Differential Output Voltage Amplitude2 ΔVout 300   850 mVp-p
Input Logic Level High VIH 2.0   Vcc V
Input Logic Level Low VIL 0   0.8 V
Output Logic Level High VOH Vcc-0.5   Vcc V
Output Logic Level Low VOL 0   0.4 V

Note:

1. Differential input voltage amplitude is measured between TxnP and TxnN.

2. Differential output voltage amplitude is measured between RxnP and RxnN.

 

Optical Characteristics 

 

 

 

 

 

Want to know about this product?

SEND A MESSAGE
Leave A Message

If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.

Related Products
200G QSFP56 FR4 2KM 200G QSFP56 FR4 2KM LC PAM4 Optical Transceiver
Features 4 duplex channels transmitters and receivers Integrated CWDM LD and PD array LC/UPC connecting interface compliant Single +3.3V power supply DDM function implemented Hot-pluggable QSFP56 form factor Transmission length up to 2km Low power dissipation:
Read More
200G QSFP56 SR4 200G QSFP56 SR4 100m 850nm PAM4 Transceiver
Features QSFP56 Serial Optical Interface 4x50G PAM4 retimed 200GAUI-4 C2M electrical interface MPO-12 connector 4 channel VCSEL array and 4 channels PIN photodetector array >Maximum link length of 70m on OM3 or 100m on OM4   QSFP MSA Compliant Hot Pluggable QSFP56 form factor Compliant with SFF8636 Rev 2.10a   Support Protocol Compliant with IEEE 802.3cd   Low Power Consumption Less than 5W in temperature range of 0 to 70℃   Applications 200GBASE-SR4200G Ethernet Data center  
Read More
200G QSFP-DD SR8 Transceiver 200G QSFP-DD SR8
Features：   Up to 28.05 Gbps data rate per channel by NRZ modulation Support 200GAUI-8 electrical interface Integrated 850nm VCSEL array and PD array Hot-pluggable QSFP-DD form factor Supported MPO-16 APC or 2*MPO-12 UPC Compliant to QSFP-DD HW Compliant with CMIS 4.0 Maximum power consumption 3.5W Single 3.3V power supply Case operating temperature 0°C to 70°C Class 1 laser   RoHS compliant
Read More
200G QSFP56 DOC cable 200G QSFP56 DAC Transceiver
QSFP56 MSA, Up to 4x 53.125Gb/s, 200G DAC cable High reliability 850nm VCSEL technology Electrically hot-pluggable Low power consumption Low EMI design
Read More
10G SFP+ Transceiver 10G ZR 100KM SFP+ Optical Transceiver
10G ZR SFP+ optical transceiver module, support 10Gb/s and up to 100km transmission, It works in high-speed IDC connection solutions, 5G network front-haul solution, network switch, PTN, OTN, SONET OC-192 / SDH,10G Fibre Channel and so on. Features: Supports 9.95 to 11.3Gb/s bit rates Hot-Pluggable Duplex LC connector 1550nmcooledEMLtransmitter,APD photo-detector SMF links up to100km 2-wire interface for management specifications compliant with SFF 8472 digital diagnostic monitoring interface Power Supply :+3.3V Power consumption<1.8W Temperature Range: (Commercial) 0°C~ 70°C / (Industrial)-40°C~85°C RoHS compliant
Read More
8ch DWDM MUX DEMUX Dual Fiber 8CH C41-C48 DWDM MUX DEMUX
IL<2.4dB , 100GHZ DWDM MUX DEMUX Multiplexing of 8 Channels over a Dark Fiber Network Fully Compatible with All ITU-T 1G/10G/25G/40G/100G DWDM Optics Passive devices, No Power No Cooling Required Support Metro, Regional and Long Haul DWDM Networks
Read More
Single fiber 100G DWDM MUX DEMUX Single Fiber 8CH (16waves) DWDM MUX/ DEMUX, With 1330nm Port
IL<3.5dB , 100GHZ DWDM MUX/ DEMUX, 1310nm port can support 10G bidi 1270/1330nm Mon port is for network link monitoring or power monitoring, easy troubleshooting without affecting traffic. Expansion Port for Future Bandwidth Increasing, makes it possible to increase the network capacity by connecting it to the line port of another DWDM MUX/DEMUX supporting different wavelengths, without the need of installing or leasing additional fibers.
Read More
PLC 2.0MM 1.0M Fiber DIN Mounting Box 1x4 PLC SC/UPC 2.0MM 1.0M Fiber DIN Mounting Box 120*110*20MM
Fiberwdm’s PLC are developed based on unique silica glass waveguide process with reliable precision aligned fiber pigtail in a miniature package, it provides a low cost light distribution solution with small form factor and high reliability. The PLC devices have high performance in terms of low insertion loss, low PDL, high return loss and excellent uniformity over a wide wavelength range from 1260nm to 1620nm and working in temperature from -40℃ to +85℃. The PLC devices have standard configurations of 1*4, 1*8, 1*16 and 1*32 configurations, as well as customized structures of 2*8, 2*16, 2*32 and 2*64
Read More
contact us
Subscribe
Subscribe to our newsletter and stay up to date with the latest news and deals!
  • f
  • tw
  • you
  • in
  • ins
Copyright © 2013-2026 Guangzhou Ruid Ele-tech CO., LTD.. All Rights Reserved. 粤ICP备2023059768号 | Privacy Policy | Sitemap | XML |
IPv6 network supported
Leave A Message
Leave A Message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.
Refresh the image

Home

Products

about

contact