Detectors of this series are directly interchangeable with Thorlabs' battery-equipped products and perform no worse than Thorlabs' similar products in all aspects. In addition to detectors with existing specifications, customization services are also available. Various parameters of the detector (such as supply voltage, bandwidth, etc.) can be adjusted according to customer requirements to meet specific application needs. This series is specifically designed for laser measurement systems. It has no gain amplification, comes with a built-in battery, and serves as a cost-effective detector product for high-power laser laboratories.

IL

To meet domestic customers' demand for fully localized high-speed photodetector (PD) products, Fiberwdm has developed two high-speed PD products with bandwidths exceeding 18GHz and 40GHz after nearly 2 years of R&D and optimization. The 18GHz PD has a rise time of less than 20ps, and the 40GHz PD has a rise time of less than 8.5ps. Their responsivity is no lower than that of similar imported products from Finisar, Thorlabs, etc., and the tail oscillation is also well controlled. This series of high-speed detectors does not include a Transimpedance Amplifier (TIA) and features extremely low noise. It can be used for testing high-speed communication systems and femtosecond laser systems, and is a cost-effective fully localized product. The linear power supply independently developed by Fiberwdm can fully meet the requirements of high-speed detectors in scientific research applications.

150GHz C-band Flat top 32-Channel Athermal AWG, DWDM MUX DEMUX LC/UPC 1U RACK     Introduction   The 150GHz 32ch DWDM MUX DEMUX operate in C-band. And it meet the following specification over the operating temperature.   Definition Note:    All specifications should be guaranteed at the worst-case polarization state and over the entire operating environmental condition and end of life. The Insertion Loss of a device is defined as the maximum loss at a defined wavelength, taking into account the worst-case polarization state over the full operating temperature range. The Insertion Loss Uniformity of a device is the difference between the insertion loss of the best-case and worst-case channels. The Polarization Dependent Loss of a device is the maximum insertion loss difference between all polarization states at the defined wavelength. The Reference Passband is defined as a band of wavelengths around each center wavelength. It is used in the definition of crosstalk. The Adjacent Isolation of channel is the maximum insertion loss difference from the mean transmission at the ITU grid wavelength to the highest power over the all polarization and the ITU band of two adjacent channels. The Non-adjacent Isolation of channel is the maximum insertion loss difference from the mean transmission at the ITU grid wavelength to the highest power over the all polarization and the ITU band of the non-adjacent channels. The Total Crosstalk of channel is the total cumulative insertion loss difference from the mean transmission at the ITU grid wavelength to the highest power over the all polarization and the ITU band of all other channels including adjacent and non-adjacent channels. The Wavelength Accuracy is defined as the maximum difference between the defined wavelength and the center of measured 3dB passband.   Product Penal                           150GHz DWDM MUX DEMUX 32CH 1U Rack Technical Parameter   Parameter Specification Units Notes Min Type Max Channel Spacing 150 GHz   Nos of Channel 32 Ch   Channel Frequencies ITU Grid THz   Available Channel Frequency Range 191.2   196.7 THz   Channel Passband -60   +60 GHz   -0.48   +0.48 nm   Center Wavelength Accuracy -0.05   +0.05 nm   -6.25   +6.25 GHz   Insertion Loss     5.5 dB @Center Wavelength     6.0 dB Full Bandwidth Passband Ripple     0.6 nm Full Bandwidth Bandwidth @1.5dB 135     GHz   Bandwidth @3.0dB 160     GHz   Bandwidth @20dB     310 GHz   Insertion Loss Uniformity at ITU     1.50 dB   Polarization Dependent Loss     0.5 dB   Adjacent Channel Isolation 13 15   dB   Non-Adjacent Channel Isolation 30 35   dB   Total Cross Talk 11 13   dB   Directivity 50     dB   Return Loss with connectors 40 45   dB   Chromatic Dispersion -20   +20 ps/nm   PMD     0.5 ps   Optical Power Handling of Common Port     24 dBm     Operating Conditions   Parameter   Min Max Units Temperature   -5 70 ℃ Humidity Non-condensing 0 90 % R.H.   Storage Conditions   Parameter   Min Max Units Temperature   -40 85 ℃ Humidity Non-condensing 0 90 % R.H.   Channel Plan 32Port AWG - On grid   The AWG operate in C-band. The channels are as follows Table 1   Channel ITU Frequency Wavelength Channel ITU Frequency Wavelength No. Channel THz nm No. Channel THz nm 1   191.4000 1566.314 17   193.8000 1546.917 2   191.5500 1565.087 18   193.9500 1545.720 3   191.7000 1563.863 19   194.1000 1544.526 4   191.8500 1562.640 20   194.2500 1543.333 5   192.0000 1561.419 21   194.4000 1542.142 6   192.1500 1560.200 22   194.5500 1540.953 7   192.3000 1558.983 23   194.7000 1539.766 8   192.4500 1557.768 24   194.8500 1538.581 9   192.6000 1556.555 25   195.0000 1537.397 10   192.7500 1555.343 26   195.1500 1536.216 11   192.9000 1554.134 27   195.3000 1535.036 12   193.0500 1552.926 28   195.4500 1533.858 13   193.2000 1551.721 29   195.6000 1532.681 14   193.3500 1550.517 30   195.7500 1531.507 15   193.5000 1549.315 31   195.9000 1530.334 16   193.6500 1548.115 32   196.0500 1529.163   Table 2   Channel ITU Frequency Wavelength Channel ITU Frequency Wavelength No. Channel THz nm No. Channel THz nm 1   191.3625 1566.621 17   193.7625 1547.216 2   191.5125 1565.394 18   193.9125 1546.019 3   191.6625 1564.169 19   194.0625 1544.824 4   191.8125 1562.945 20   194.2125 1543.631 5   191.9625 1561.724 21   194.3625 1542...

The HSPD4040 high-speed detector module is designed for both digital and analog applications. The module contains an InGaAs PIN photodiode which response wavelength covers 1250 to 1650 nm and necessary matching electronics. HSPD4040 can provide the bandwidth upto 40GHz .  The module operates on +5V. It complies with a standard single-mode 9/125μm fiber input. The RF output port is a 2.92 mm connector matched by 50 ohm impedance . HSPD4040 is hermetically sealed, and weighs less than 20 grams. ROHS 2.0 certificated . 

1310nm port can support 1G LX/SX, 10G LR, 40G ER4/LR4, 100G LR/ER4/LR4/ZR4; it for Existing Legacy Traffic. Mon port is for network link monitoring or power monitoring, easy troubleshooting without affecting traffic.

To meet the demand of domestic customers for the full localization of high-speed detectors with amplification, Fiberwdm has launched a product with a bandwidth exceeding 20GHz. This series of high-speed detectors comes with built-in amplification and features extremely low noise. It can be used in high-speed communication systems and femtosecond laser system testing, making it a cost-effective, fully localized product. Fiberwdm has independently developed a linear power supply, which can fully meet the needs of high-speed detectors in scientific research applications.

IL<3.5dB , 100GHZ DWDM AAWG Technology Multiplexing of 40 Channels with 1310nm and Monitor a Dark Fiber Network Fully Compatible with All ITU-T 1G/10G/25G/40G/100G DWDM Optics Passive devices, No Power No Cooling Required Support Metro, Regional and Long Haul DWDM Networks

The PCIe-6920 is a PCIe x8 Lane, dual-channel, 14bits resolution, high-speed data acquisition card with 250MSps sampling rate.Onboard high-performance FPGA chip with rich multiplier and RAM resources. By adopting high-capacity data cache and high-speed data transmission technology, it supports real-time uploading of raw data, and the data transmission rate can be up to 2GB/s. The driver has good compatibility, and it supports multiple versions of 32/64bits of WIN7, WIN8, WIN10, CentOS and Ubuntu system.

Supports 40G/100G LR4, ER4, ZR4, dual fiber to single fiber Operation wave 1310nm（ 40G/100G LWDM 4 or CWDM 4) TX/RX LC Connector , LINE SC/APC Passive device, Low Insertion Loss

Fiberwdm's APD Avalanche Photodetector is fully domestically produced. Adopting an exclusive temperature compensation technical solution, it achieves high sensitivity. The detector maintains high stability, high gain, and low noise throughout the entire temperature range (-40°C to 80°C). In addition to detectors with standard specifications, customized services are also provided. Various indicators of the detector (such as supply voltage, gain, bandwidth, etc.) can be adjusted according to customer needs to meet specific requirements. Application Fields: Lidar, free-space optical communication, fiber optic sensing systems, optical detection systems, etc.

IL<5.5dB, 75GHZ DWDM AAWG Technology Multiplexing of 64 Channels in a Dark Fiber Network 64 * 400G DCI transfer system Passive devices, No Power No Cooling Required Support Metro, Regional and Long Haul DWDM Networks